93*95*82 мм
Позиция | Выходное напряжение | Выходной ток | ||||
Выходы | -10 В ~ +10 В | 0 В ~ +10 В | 0 В ~ +5 В | 1 В ~ +5 В | 0 ~ 20 мА | 4~20 мА |
Разрешение | 5 мВ | 2.5 мВ | 1.25 мВ | 1.25 мВ | 5 мкA | 5 мкA |
Сопротивление выхода | 1 KОм @ 10 В | >= 500 Ом @ 5 В | ||||
Максимальный ток | 10 мА | |||||
Время срабатывания | 3 мс | |||||
Разрядность ЦАП | 12 бит | |||||
Точность | 0.2% от диапазона | |||||
Способ изоляции | Оптоизоляция аналоговой части (нет изоляции между входами) | |||||
Потребление | 24VDC ±20%,100 мА(Макс) |
Item | Voltage Output | Current Output | ||||
Output range | -10V ~ +10V |
0V ~ +10V |
0V ~ +5V |
1V ~ +5V |
0 ~ 20mA |
4~20mA |
Resolution | 5mV | 2.5mV | 1.25mV | 1.25mV | 5μA | 5μA |
Output load impedance | 1KΩ@10V | ≥500Ω@ 5V | ≤500Ω | |||
Output indication | LED light means normal | |||||
Drive capability | 10mA | |||||
Response time | 3ms | |||||
Digital output range | 12 bits, Code range: 0~32000(H series module 16 bits D/A convert) | |||||
Precision | 0.2% F.S | |||||
Power supply | MPU use internal power supply, Extension module use external power supply 24VDC ±10% 5VA |
|||||
Isolation mode | Opto-electric isolation, Non-isolation between Channel, between analog and digital is opto-electric isolation |
|||||
Power consumption | 24VDC ±20%,100mA(Max) |
CR Number | Function Declare |
S08AO | |
00H (Read only) | The low byte is the module code, and the high byte is the module version number. |
01H | Communication address |
02H | Communication protocol: The low 4-bit of the low bytes:0 - N,8,2 For RTU,1 - E,8,1 For RTU, 2 - O,8,1 For RTU,3 - N,7,2 For ASCII,4 - E,7,1 For ASCII,5 - O,7,1 For ASCII,6 - N,8, 1 For RTU |
The high 4-bit of the low bytes: 0 – 2400,1 – 4800,2 – 9600,3 – 19200,4 – 38400, 5 – 57600,6 - 115200 |
|
03H~06H | Extend module name |
07H~08H | Default IP address: 192.168.1.111 |
09~0AH (Read only) | Reserve |
0BH | High byte subnet mask(b3~b0,1 indicates 255,0 indicates 0 , for example, subnet mask 255.255.255.0, b3~b0=1110), low byte Reserved |
0CH~0EH (Read only) | Reserve |
0FH (Read only) | Error code: 0-Normal, 1-Illegally firmware identity, 2-Incomplete firmware, 3-System data access exception, 4-No external 24V power supply |
10H | The output value of channel 1 |
11H | The output value of channel 2 |
12H | The output value of channel 3 |
13H | The output value of channel 4 |
14H | The output value of channel 5 |
15H | The output value of channel 6 |
16H | The output value of channel 7 |
17H | The output value of channel 8 |
18H | The signal type of channel 1, note 2 |
19H | The signal type of channel 2, note 2 |
1AH | The signal type of channel 1, note 2 |
1BH | The signal type of channel 4, note 2 |
1CH | The signal type of channel 5, note 2 |
1DH | The signal type of channel 6, note 2 |
1EH | The signal type of channel 7, note 2 |
1FH | The signal type of channel 8, note 2 |
20H | Use the engineering value mark, note 6 |
21H | The lower limit in engineering value of channel 1 |
22H | The lower limit in engineering value of channel 2 |
23H | The lower limit in engineering value of channel 3 |
24H | The lower limit in engineering value of channel 4 |
25H | The lower limit in engineering value of channel 5 |
26H | The lower limit in engineering value of channel 6 |
27H | The lower limit in engineering value of channel 7 |
28H | The lower limit in engineering value of channel 7 |
29H | The upper limit in engineering value of channel 1 |
2AH | The upper limit in engineering value of channel 2 |
2BH | The upper limit in engineering value of channel 3 |
2CH | The upper limit in engineering value of channel 4 |
2DH | The upper limit in engineering value of channel 5 |
2EH | The upper limit in engineering value of channel 1 |
2FH | The upper limit in engineering value of channel 7 |
30H | The upper limit in engineering value of channel 1 |
31H | Power-off output mark, note 8 |
32H | The power-off output value of channel 1 |
33H | The power-off output value of channel 2 |
34H | The power-off output value of channel 3 |
35H | The power-off output value of channel 4 |
36H | The power-off output value of channel 5 |
37H | The power-off output value of channel 6 |
38H | The power-off output value of channel 7 |
39H | The power-off output value of channel 8 |
3AH (Read only) | Channel indicator status, note 7 |
3BH (Read only) | Reserve |
3CH (Read only) | |
3DH (Read only) | |
3EH (Read only) | |
3FH (Read only) | |
40H (Read only) | |
41H (Read only) | |
42H~4FH (Read only) |
Характеристики | |
Интерфейсы: | 1xEthernet, 1xRS485 |
Каждый AI модуль поддерживает шесть типов сигналов: [4,20]mA, [0 | |
Точки ввода/вывода: | 8AO |